Call Today

 

Were you trying to find info concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Installing a bath tub isn't exactly rocket science, however it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately difficult task. If the old tub is readily available, the project can relocate easily; if you have to open up a wall surface to eliminate the old bathtub as well as place the new tub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and also embeded in the brand-new one. Make sure you have certified on your own for the job and are comfortable trying it. Rather than employing a specialist to take control of a halfway-completed project, it is better to consider using one before you begin. Chances are you might require a professional plumber to make tube links.
This short article will certainly help you set up a brand-new bath tub in your washroom if you have actually currently bought a new bathtub and do not need to change the arrangement of your previous supply of water pipes.
Your tools as well as material checklist ought to make up the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Preparing for the Installation

First of all, the supporting framework supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets unit to stop pressure on the bath tub.
Fit the versatile tap adapters to the bottom of both taps utilizing 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last setting.

 

 

Removing Old Taps

If you require to replace old taps with new ones as a part of your installment, after that the first thing you need to do is disconnect the water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be fairly troublesome as a result of the limited gain access to that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

 

 

Installing the Tub

Making use of both wooden boards under its feet, position the bath tub in the needed placement. The wooden boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the bathtub until the level reviews level.
To set up faucets, fit all-time low of the outermost versatile tap adapter to the proper supply pipeline by making a compression join; after that do the same for the other faucet.
Activate the water system and check all joints as well as new pipework for leaks as well as tighten them if needed. Load the bath tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub ought to wait up until the tub has actually been made use of at least when as this will resolve it into its final placement.

 

 

Fitting New Touches

If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washing machines are in area in between the faucet and the sink. Safeguard the tap in position with the maker offered backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet connectors. The former kind needs to be linked to the faucet finishes first, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Tub

In the location where the bath fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack a rigid seal, triggering the water to penetrate the wall in between the bathroom and the tiling, resulting in difficulties with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill the tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealant can fracture relatively early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily readily available on the marketplace. It is suggested to fit the tiles making use of water-resistant or water-proof sticky and also cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Do you like reading about How to Install a Bathtub Yourself? Put a comment down below. We'd be delighted to know your ideas about this blog posting. We are looking forward that you visit us again later on. Sharing is good. Helping people is fun. Many thanks for your time. Visit us again soon.

The best? Call us!